Marin Bikes

Alpine Trail E1

MY21 Marin AT E1 P Final

See this bike in a different color:
  • Suspension: RockShox 35 Gold RL 29" / Rock Shock Super Deluxe Coil R
  • Wheel Size: Mixed 29"/27.5"
  • Frame: Aluminum
  • Size Range: S, M, L, XL

MOUNTAIN BIKING WITH A BOOST

BEYOND CAPABLE, BOTH UP AND DOWN, IN EVEN THE MOST CHALLENGING TERRAIN

MAXIMIZING FUN

The Alpine Trail E will take you further, faster, allowing you to tackle the most aggressive trails either up or down.

Jump to…

Specifications

  • FRAME

    All New Series 4 Alloy Frame, 150mm Multitrac suspension, Integrated Battery/On-switch/Charging Port, 148mm Rear Thru-Axle, Built-in Rear Speed Sensor

  • FORK

    Rock Shock 35 Gold RL 29", Motion Control Damper, 160mm Travel, Maxle Stealth Axle, 44mm Offset

  • SHOCK

    Rock Shock Super Deluxe Coil R, Rebound Adjustment, 205x65mm, 25mmxM8 Lower Hardware, S/M Spring Rate = 300lb, L/XL Spring Rate = 400lb

  • RIMS

    Front: Marin Aluminum Double Wall, 29" Diameter, 32mm Inner Rim Width, Pinned Joint, Disc Specific, Tubeless Compatible; Rear: Marin Aluminum Double Wall, 27.5" Diameter, 38mm Inner Rim Width, Pinned Joint, Disc Specific, Tubeless Compatible

  • HUB REAR

    Shimano HB-MT400B, 148x12mm, Centerlock, Standard Freehub Body

  • HUB FRONT

    Shimano MT-410B, 110x15mm, Centerlock Disc, 32H

  • SPOKES

    14g Black Stainless Steel

  • TIRES

    Front: Maxxis Assegai 29x2.5", 3C MaxxTerra, Double Down, Tubeless Compatible Rear: Maxxis Minion DHR II 27.5x2.8, 3C Maxx Terra, EXO+, Tubeless Compatible

  • DERAILLEUR REAR

    Shimano Deore 5100 Direct Attachment, 10-Speed

  • DERAILLEUR FRONT

    -

  • SHIFT LEVER

    Shimano Deore M4100-R, I-Spec EV, 10-Speed

  • CRANKSET

    Marin Forged Alloy 165mm Length, Narrow Wide 38T Chainring, e13 Plus Chain guide, Aluminum Plate

  • MOTOR

    Shimano STEPS E7000, 250W, 60Nm

  • CHAIN

    KMC X-10E, E-Bike Specific, Silver

  • CASSETTE

    Shimano Deore M4100-10 10-speed 11-46T

  • BRAKES FRONT

    Shimano MT420, 4-Piston Hydraulic Disc Brake, 203mm Rotor

  • BRAKES REAR

    Shimano MT420, 4-Piston Hydraulic Disc Brake, 203mm Rotor w/ Speed Sensor

  • BRAKE LEVERS

    Shimano MT4100 Hydraulic Lever, I-Spec EV Compatible

  • HANDLEBAR

    Marin Mini-Riser, 6061 Double Butted Aluminum, 780mm Width, 28mm Rise, 5º Up, 9º Back

  • STEM

    Marin 3D Forged Alloy, 35mm

  • GRIPS

    Marin Single Clamp Locking

  • HEADSET

    FSA No 57, Sealed Cartridge Bearings, 1 1/8" x 1 1/2”

  • SEATPOST

    TranzX, YSP23JL, 1x Remote, Size S 125mm Travel, Size M and L 150mm Travel, Size XL 170mm Travel, 30.9mm

  • SADDLE

    Marin E-MTB Saddle

  • PEDALS

    Marin MTB Plastic

  • BATTERY

    BT-8035, Internal 504Wh

  • DISPLAY

    SC-E7000 Display

  • SWITCH

    SW-E7000 Left Hand Switch for Assist Mode Change

  • EXTRAS

    Shimano Battery Charger EC-E6002, Bolt-on Thru-Axle

Specifications, pricing, and availability are subject to change without notice.

Geometry

Alpine Trail E1 geometry diagram
S M L XL
Stack 613 622 631 640
Reach 445 465 485 505
Headtube Angle 63° 63° 63° 63°
Headtube Length 100 110 120 130
Seattube Angle 78° 78° 78° 78°
Seattube Length 390 400 425 430
Toptube Effective 575 597 619 641
BB Height 340.5 340.5 340.5 340.5
BB Drop 28 28 28 28
Chainstay 435 435 435 435
Wheelbase 1215 1239 1264 1288
Standover Height 681.6 681.4 686.8 689.8
Fork Offset 44 44 44 44
Seatpost Diameter 30.9 30.9 30.9 30.9
Handlebar Width 780 780 780 780
Stem Length 35 35 35 35
Crank Length 165 165 165 165

All lengths in millimeters

Suspension Setup

REAR SHOCK SET UP

Recommended Sag = 30%/19.5mm

Step 1: Set correct pressure in rear shock.

Step 2: Sit on the bike and cycle the suspension (*with correct riding gear).

Step 3: Reset O-ring and sit on the bike, DO NOT BOUNCE, carefully step off.

Step 4: Measure sag (from o-ring to seal of shock), If it does not match the bike’s recommended sag in millimeters repeat process.

Step 5: Adjust rebound setting to ensure proper control.

FORK SET UP

Marin recommends that all bikes front and rear suspension feel balanced

Step 1: After rear sag is set follow the recommended pressure from the fork manufacture.

Step 2: Bounce evenly up and down on the bike, cycling the suspension up and down to make sure both front and rear suspension feel balanced, if the front does not match the rear add or release pressure.

Step 3: Once the bike feels balanced adjust the rebound damping to ensure proper control.

Rock Shock Super Deluxe Coil R

Rider weight and shock setup
LBS KG COIL LB/IN
120 54 300
130 59 300
140 64 300
150 68 300
160 73 350
170 77 350
180 82 350
190 86 400
200 91 400
210 95 400
220 100 400
230 104 450
240 109 450
250 113 450
260 118 450
270 122 450

Reviews

A brilliantly fun ebike from Marin that is built to shred trails and downhill.

Motorised radness on a budget.

This is way too fun!

You May Also Like